Start Here: Know Which System Your Truck Has
Before you upgrade your Silverado's audio, the most important step isn't picking speakers. It's figuring out whether your truck has the Bose system or the standard (non-Bose) system, and whether it's a pre-2019 or 2019-and-newer model. Those two answers decide whether you can simply swap speakers, whether you need an amp, and how the whole system gets wired.
The Silverado's cab is roomy, and it's a lot noisier than a sedan — road noise, tire roar, and engine rumble all compete with your music. Factory speakers have limited power and basic cone materials, so once you hit highway speeds, vocals get muddy and the bass falls flat. Almost every owner has noticed it.
This guide takes Diamond Audio's engineering perspective and walks you through four things: identifying your factory system, understanding the real difference between Bose and non-Bose setups, confirming speaker sizes by model year and cab style, and choosing the right upgrade path from our DMDX and HEX PRO speaker lines.
Step 1: Identify Your System
The most reliable method is to check your RPO (Regular Production Option) codes. On 2019–2023 trucks, UQF means the standard 6-speaker system, and UQA means the Bose premium 7-speaker system. You can pull up these codes by scanning the QR code on the driver's door. If you also see NKC, your truck has Active Noise Cancellation, which needs special attention when you add an amp later.
No scanner handy? Cross-check these three clues:
- Speaker grilles: Bose trucks usually have a Bose logo on the door speaker grilles.
- External amplifier: The Bose amp is mounted behind the rear seat on the passenger side. On 2014–2018 trucks it sits on the back wall of the cab; on 2022 and newer trucks it's below the rear window, down near the floor.
- Center console subwoofer: Bose trucks have a factory sub in the center console. Non-Bose trucks don't.
Also note your cab style: Regular Cab, Double Cab, or Crew Cab. It determines where your rear speakers are and what size they are.
Bose vs. Non-Bose: What Actually Differs
Both systems put speakers in nearly the same locations. The difference is how those speakers are driven — and that decides how much you'll gain from new speakers.
Amplification: Head Unit Power vs. External Amp
In non-Bose trucks, the amp chip inside the radio drives the speakers directly. On 2019-and-newer non-Bose trucks, that tuner/amp module is tucked beside the glovebox. Its output is limited, so new speakers alone will improve clarity, but adding an amp is where the big jump happens.
Bose trucks use a separate external amplifier to power every speaker, and that amp also handles crossover and EQ processing.
Impedance: The Most Overlooked Issue
Non-Bose factory speakers are a standard 4 ohms, the same as most aftermarket speakers — including Diamond Audio's DMDX series — so they're a direct swap.
Bose speakers usually run at a lower impedance, and it varies by model year and location. For example, on 2014–2018 trucks the Bose console subwoofer is just 0.9 ohms. On 2022-and-newer refreshed trucks, owners have reported conflicting readings for the door and dash speakers. So our advice is simple: don't buy speakers based on numbers you found online. Measure your factory speakers with a multimeter, or check the label on the back.
If you connect 4-ohm speakers to a Bose amp designed for a lower-impedance load, the amp delivers less power — which usually means lower volume and thinner bass.
Signal Processing: The Bose Amp Is Already “Tuned”
The Bose amp applies crossover and EQ settings built around the factory speakers. Once you install new speakers, that tuning no longer matches. For example, the crossover point between the front doors and the dash is still set for the factory drivers, so your new speakers can't reach their full potential.
2019 and Newer: Ethernet Amplifiers
This is something most upgrade guides don't explain clearly. On 2019-and-newer Silverados with Bose, the radio sends digital audio to the amp over Ethernet. The traditional approach — tapping high-level signals off the amp's speaker outputs to feed an aftermarket amp — doesn't work on these trucks. You need an integration interface built specifically for GM Ethernet audio systems, and some of them require removing the factory amp.
Silverado Speaker Size Quick Reference
On 2014-and-newer Silverado 1500s, the front doors take 6x9s and the dash takes 2.75-inch speakers. What changes is the rear. The table below combines data from Crutchfield's 2014–2018 teardown research and Crutchfield's 2024 fit database.
|
Location |
2014–2018 |
2019 and newer |
|
Dash corners |
2.75" (all trucks) |
2.75" |
|
Front doors |
6x9" |
6x9" |
|
Rear doors (Crew Cab) |
6.75" |
6.5" |
|
Rear doors (Double Cab) |
6.75" |
Verify before buying |
|
Rear pillars (Regular Cab) |
4x6" |
Verify before buying |
|
Center console sub (Bose only) |
6" oval, down-firing, 0.9 ohms |
Present; measure to confirm specs |
Three things to keep in mind during install:
- There's no wiring harness adapter for the dash location. You'll need to splice or use solderless connectors, and secure the new speaker with a bracket.
- The 6x9 front doors need adapter brackets. 2014-and-newer trucks have vehicle-specific brackets and plug-in harnesses available, so there's no need to cut factory wiring.
- Sizes you find online aren't always reliable. Some sources list the 2014–2018 rear doors as 5.25" or 6.5", which doesn't match measured data. Before you order, double-check with a vehicle fit tool using your model year and cab style.
Path 1: Non-Bose Trucks — The Most Straightforward Upgrade
Non-Bose owners have it easiest. The factory speakers are 4 ohms, and so is the Diamond Audio DMDX series — a natural impedance match. You can tackle the upgrade in two stages.
Stage 1: Install DMDX Speakers
The DMDX series is Diamond Audio's line built specifically for factory-system upgrades, with 21 models covering everything from 2.5" up to 6x9". The component sets include separate tweeters and external crossovers, delivering noticeably better imaging and vocal clarity than factory paper-cone speakers.
Here's what we recommend by location:
- Front doors (6x9): The DMDX69C 2-way component set (65W RMS, 88 dB, 4 ohms, 3.17" mounting depth), or the more budget-friendly DMDX69 coaxial.
- Front doors + dash in one kit: The DMDX6925C 3-way 6x9 set comes with a pair of DMDX25 2.5" speakers — a perfect match for the Silverado's 6x9-door-plus-small-dash layout. Note that the dash opening is 2.75", so the 2.5" drivers need an adapter ring or bracket.
- Rear doors: For 2014–2018 trucks, choose a DMDX 6.75" model. For 2019-and-newer Crew Cabs, go with a DMDX 6.5" model (such as the DMDX65C).

6" x 9" DMDX Series 3-Way Component Set - DMDX6925C
Stage 2: Add a DSP Amplifier
The factory radio's output is limited, and with an 88 dB sensitivity rating, the DMDX69C needs real power to deliver its full midbass punch. We recommend the Diamond Audio NEO12004DSP:

4-Channel 1200W RMS CLASS D Amplifier with 6CH DSP - NEO12004DSP
- 4 channels: 150W per channel at 4 ohms, 300W per channel at 2 ohms.
- Accepts a 0.4–20V input range, so it can take factory high-level signals directly — no new head unit required.
- Built-in full 6-channel DSP lets you set crossovers, EQ, and time alignment for each speaker individually.
If you drive a 2019-or-newer truck, keep the factory screen. On newer Silverados, the “head unit” is really a display integrated with vehicle functions, and replacing it is extremely complicated. Adding a DSP amp on the signal side is the safer route.
Path 2: Bose Trucks, Keeping the Factory Amp — Why We Don't Recommend It
Swapping speakers while keeping the Bose amp looks like the easiest option, but the payoff is limited. Here's why, before you spend the money:
- Impedance mismatch: The Bose amp is designed for low-impedance speakers. Connect 4-ohm speakers and its power output drops — your new speakers may actually play quieter than the factory ones.
- Mismatched factory tuning: The crossover and EQ built into the Bose amp were written for the factory drivers, and new speakers have a completely different frequency response.
- Power ceiling: The factory amp's total output is limited. Better speakers can't push past it.
If your budget really only covers speakers, measure your factory speakers' impedance first and choose products that match closely. But for long-term results and value, we strongly recommend going straight to Path 3 and getting the signal chain right the first time.
Path 3: Bose Bypass + DSP Amplifier (Recommended)
For Bose owners, the best-performing solution is to let an aftermarket DSP amp take over the factory amp's job. That solves impedance, crossover, and power all at once — and gives your DMDX speakers the clean signal and headroom they need.
2014–2018 Trucks
On this generation, an integration interface pulls signal from the factory system and feeds it to your aftermarket amp. Two things to watch:
- If you keep the factory center console sub, it's only 0.9 ohms and needs an amp that's stable into low impedance.
- Higher trims have Active Noise Cancellation, which must be addressed before you add an amp (see “Three Things You Shouldn't Skip” below).
2019 and Newer
Bose trucks from this generation use Ethernet amplifiers, so you'll need an integration interface designed specifically for GM Ethernet audio. A good interface should:
- Retain factory chimes, including parking sensor alerts.
- Retain OnStar voice prompts and play them through your aftermarket amp.
- Output a full-range signal ready for DSP tuning.
Some interfaces require removing the factory amp, so check the product's fitment notes before you install.
Recommended Pairing
- Speakers: DMDX69C or DMDX6925C in the front doors, DMDX 6.5" or 6.75" models in the rear — all 4 ohms.
- Amplifier: The 4-channel NEO12004DSP is a great fit for a front-and-rear 2-way system. If you plan to run the front stage actively and add a sub, the 6-channel NEO15006DSP (onboard 8-channel DSP, 150W per channel at 4 ohms) gives you more room to grow.
This path costs more than a simple speaker swap, but it's the only way to unlock the full performance of aftermarket speakers in a Bose truck.
Path 4: The HEX PRO Reference System
If you're chasing reference-grade soundstage and detail, HEX PRO is the most advanced speaker series in the Diamond Audio lineup, built for serious audiophiles and high-end custom builds. It's not a drop-in upgrade — it's a system that calls for custom installation and professional tuning.
The Flagship: HXPRO653DI Diamante Italia Edition
This 6.5" 3-way component system was developed at Diamond Audio's acoustic research center in Tuscany, Italy, with one goal: reproduce the true tone of real instruments and natural vocals. It's built from three drivers:
- 6.5" midbass: Delivers the weight and impact of the low-mid range.
- 3" midrange: Handles vocals and the body of most instruments — the key to a 3-way system's soundstage clarity.
- 1" natural silk dome tweeter: With a Kapton voice coil former and neodymium motor, it delivers smooth, detailed highs without harshness.

6.5" HEX PRO Diamante Italia Edition 3-Way Component Set - HXPRO653DI
How It Fits in a Silverado
- Midbass: Mounts in the factory 6x9 front door location using a 6x9-to-6.5" adapter or custom door pods.
- Midrange: A 3" driver won't fit the 2.75" dash opening. We recommend custom A-pillar pods — 3.5" A-pillar pods made for the Silverado are already on the market — so the midrange and tweeter sit together, close to ear level.
- Tweeter: Shares the A-pillar with the midrange for a higher, more stable stereo image.
The Amplifier It Needs
HEX PRO is designed for fully active, fully amplified systems. A 3-way front stage needs at least six amp channels before you add rear doors and a sub. We recommend building around the NEO15006DSP and using its DSP to set crossovers, EQ, and time alignment for each driver individually. On Bose trucks, you'll still need the Path 3 bypass first.
This is an enthusiast-level build: a bigger budget and a more involved install, but it turns your Silverado's cab into a true mobile listening room.
Three Things You Shouldn't Skip
No matter which path you choose, these three details directly affect the final result.
- Deal with Active Noise Cancellation (ANC). Higher-trim Silverados have an ANC system whose microphones can mistake vibrations from aftermarket speakers and subs for noise — causing feedback or canceled bass. When you add an amp, processor, or sub, disable it with a vehicle-specific ANC bypass harness.
- Don't skip door sound deadening. Truck doors are large panels of thin sheet metal that resonate easily. Adding damping material to the inner and outer door skins, plus foam baffles behind the speakers, noticeably tightens midbass and cuts road noise.
- Check mounting depth before you install. The DMDX69C has a 3.17" mounting depth. Before installing door speakers, roll the window all the way down and make sure the glass clears the magnet.
Adding Bass: Complete Your Truck's Low End
Door speakers handle midbass, but real low-end extension takes a subwoofer. The space under the Silverado's rear seat is the ideal spot:
- Crew Cab: A wide, shallow space under the seat — great for a slim or dual-sub under-seat enclosure.
- Double Cab: A dedicated space under the left rear seat, suited for a single compact sub.
- Regular Cab: There's almost no room behind the seat for a sub box, so you'll need to find another mounting location.
Diamond Audio under-seat enclosures and HEX PRO and DMD subwoofers pair with the amps above, and a NEO series mono DSP amp is a great match for powering your sub.
DMDX or HEX PRO? One Table to Help You Decide
Daily driver or first upgrade? Go DMDX. Chasing reference-grade sound and ready for a custom install? Go HEX PRO.
|
|
DMDX Series |
HEX PRO (HXPRO653DI) |
|
Positioning |
High-value factory upgrade |
Diamond Audio flagship, reference grade |
|
Best for |
Commuters, work trucks, first upgrades |
Audiophiles, show trucks, custom builds |
|
Impedance |
4 ohms |
Approx. 3.3 ohms |
|
Silverado fit |
Direct-fit sizes incl. 6x9, 6.5", 6.75", 2.5" |
6.5" 3-way; needs adapters and A-pillar pods |
|
Non-Bose trucks |
Direct swap; amp recommended |
Requires fully active DSP amp |
|
Bose trucks |
Pair with Path 3 bypass |
Path 3 bypass + multichannel DSP amp |
|
Install difficulty |
DIY-friendly |
Professional install recommended |
|
Price (diamondaudio.com) |
From $69.99; component sets $279.99 |
$3,299.99 |
Prices are subject to change; see diamondaudio.com for current pricing.
FAQ
Does my Silverado have Bose? How can I tell?
Scan the QR code on the driver's door to see your RPO codes: UQA is Bose, UQF is the standard system. You can also look for a Bose logo on the door speaker grilles, or check for a factory sub in the center console.
Can I put 4-ohm aftermarket speakers in a Bose truck?
They'll physically fit, but we don't recommend running them off the Bose amp. The impedance mismatch drops the amp's output, and your new speakers may end up quieter than stock. The best approach is a Bose bypass with an aftermarket DSP amp.
Can I replace the factory head unit on a 2019-or-newer Silverado?
We don't recommend it. The center screen on newer trucks integrates a lot of vehicle functions, so replacing it is very complicated. Keeping the factory screen and adding a DSP amp on the signal side is the safer upgrade.
Is the dash speaker a tweeter?
Not exactly. In the factory system it usually covers both midrange and treble. Whether you swap in a 2.75" full-range speaker or repurpose the spot as a tweeter location in a component system, you'll need the right crossover or DSP settings.
After adding an amp or sub, I'm hearing feedback or the bass keeps fading in and out. What's going on?
It's almost always the Active Noise Cancellation system. It treats sound from your new speakers and sub as noise and tries to cancel it. A vehicle-specific ANC bypass harness will shut it off.
Can I mix DMDX and HEX PRO?
Yes. A common setup is HEX PRO up front for the soundstage, with DMDX in the rear doors for fill. Because the two lines have different impedances, set the gain for each channel separately in your DSP.
The Bottom Line: Pick the Right Path, Then the Right Speakers
Upgrading your Silverado's sound comes down to a simple order of operations: confirm whether you have Bose and what model year you're working with, then choose products for that path. In non-Bose trucks, DMDX speakers plus a DSP amp deliver a dramatic improvement. In Bose trucks, start with a proper bypass, then let DMDX or HEX PRO show what they can really do.
- Want a high-value factory upgrade? Shop the DMDX series.
- Want to build a reference-grade mobile listening room? Explore the HEX PRO series.
- Need a pro install? Use the Diamond Audio dealer locator to find an authorized installer near you, or reach our tech support team at support@diamondaudio.com.
Experience Unmatched Sound with Diamond Audio.